Features

• We offers a range of SS pumps from 400 LPH to 180 M3 /Hr capacitiy in both SS304 as well as SS316.
• Pumps can be offered in horizontal as well as vertical construction also offered with variety of seal options for specific applications.
• CI range ( with wetted parts in Cast steel / SS 304 ) can be used for in line pressure boosting and for hig volume transfer.
• Non clog pumps range offer variety of impellors like agitator type, cutter type, vortex type, high clearance type, and aeration type. Max flow rate available 1500 M3/ Hr.
• High Pressure pumps offers wide pressure range upto 720 mtrs mostly demanded for Sea water desalination, High pressure boilers.

Products

Vertical Multistage Centrifugal Pumps

The Stainless Steel Vertical Multistage Centrifugal Pump is driven by standard electrical phase mountain motor. The pumps are available in complete SS 304 & complete SS 316 material. Pumps are available in I Phase as well as III Phase.

Horizontal Multistage Centrifugal Pumps.

Horizontal multistage non - self - priming centrifugal pump, attached with long shaft electric motor. Compact structure renders small size of pump ; axial inlet and radial outlet. Material of construction for the pump is complete SS 304 / SS 316 or optionally pump inlet outlet connections are cast steel & rest of the body is SS 304 / SS 316.

Horizontal Single-stage Centrifugal Pumps.

Stainless steel horizontal single stage centrifugal pump is made by advanced techniques such as pressing bulging welding of corrosion resistant plate. It is a new generation centrifugal pump and may replace traditional is pump and common corrosion proof pump. It features beautiful appearance, light and handy structure, high efficiency and energy saving, durable, corrosion proof, low noise, etc.

Horizontal Single-stage Centrifugal Pumps.

This series of pump is single-stage centrifugal pump and features axial suction and radial discharge; Compact structure, The pump is directly connected with the motor, coaxial installation; Convenient installation, screw thread water inlet and outlet; Light weight, thin plate pressing structure for main parts and components ; Corrosion resistance, components passing the flow use AISI 304 or AISI 316 stainless steel.

Multistage Deep-Well Submersible Pumps.

We offer complete range of Deep - well Submersible Pumps. Pumps are available up 6 inches diameter & are manufacture of sheet metal stainless steel. Application for this pumps include water supply for high-rise buildings, Pressure boosting unit, Irrigation, Fountains, Industrial water supply etc. Ideal operation conditions of pump are Temperature - 400 C, PH - 6 - 8, Maximum working pressure - 30 Bar.

End Suction Centrifugal Pump.

This series of pump is single-stage centrifugal pump and features axial suction and radial discharge; with pump body is fixed by base. Pump has back pull out design which facilitates easy servicing without disturbing pump body and piping. Impeller is with optimum design; large inlet avoids whirlpool; low NPSH pump; works stably with very less noise.

Features

• 2 Line Backlit LCD Display
• Rate of flow, total flow in separate line
• Versatile mounting-Pioe/Wall/Panel/Integral Mounting
• Programmable relay outputs
• 4-20mA output
• Suitable for line size from 1/2" to 48"
• Can be used for clean water-like liquids which may be acidic or alkaline
• Accourate upto+/- 1% of full scale reading
• Microprocessor based signal processing
• Easy on-site re-calibration and programmable cut off settigns
• Complete elimination of downtime with the additional of Wet tap valve assembly
• Pulsed output for dosing applications

PRINCIPLE OF OPERATION

Paddle wheel flow meters belong to the category of insertion type flow meters. The rotating paddle wheel generates o signal   in proportion to the velocity of the moving fluid which is read in terms of the flow rate.  Because the pipe's cross-sectional area is known and remains fixed   the average velocity Is an indication of the flow rate

• Flow Range - 0.5m/sec to 5m/sec
• Max. Op. Temperature - 70 deg c
• Max. Op. Pressure - 10 kg/sq.cm
• Power Supply - 230 V ~ AC / 24V DC
• Pressure Drop - < 0.1  kg/ sq.cm.

Material Of Construction

• Transducer Housing - POLYPROPYLENE
• O-rrngs - NEOPRENE
• Shaft - SS316/ HASTALLOY C/PVDF
• Rotor - PVDF
• Maximum %solids - 1% of fluid volume,non-abrasive, non-magnetic,
• <1 00 micron in diameter and length
• Max. Viscosity - 1 Cp(water) upto 5Cp above 1.5m/sec
• Output - 2-Line 16 Charater Backlit LCD Display
• Register - Rate of flow - mVhr/Total flow - m3
• Standard Cable   Length - 1.5mtrs power supply cable for field mounted
• versions and 10 mtrs  signal transmission cable for panel mounted versions
• Process Connection - ABS TEE/PP wafer drilled as per BS1 0 Table E/ ANSI Bl 6.5/ SS stub / Glue-on PVC saddle

INSTALLATION FITTINGS

All installation fittings are supplied along with the flow sensor. The sensor may be installed in a ABS TEE /PP wafer drilled as per BS10 TABLE E OR ANSI BT6.5 standards or a Glue-on PVC saddle or a SS stub welded to a MS/SS plate.